CAN I SET UP A TUB MYSELF?

Can I Set Up A Tub Myself?

Can I Set Up A Tub Myself?

Blog Article

Book Today!

Nearly everybody has got their private rationale involving How to Install a Bathtub Yourself.


A Step-by-Step Guide to Installing a Bathtub
Installing a bathtub isn't specifically brain surgery, but it does call for strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a new one is likewise a moderately hard task. If the old bathtub is easily obtainable, the task can relocate easily; if you need to open up a wall surface to eliminate the old tub and place the brand-new bath tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will require an assistant to move out the old bathtub and also embeded in the new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. As opposed to working with a service provider to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Opportunities are you might need an expert plumber to make tube connections.
This short article will aid you mount a brand-new tub in your bathroom if you have currently bought a brand-new bathtub and don't require to transform the setup of your previous water supply pipes.
Your tools and also product list need to make up the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the restricted accessibility that is often the instance.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel all set for the remaining water that will certainly come from the pipelines. When the supply pipes have been gotten rid of, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
    Before moving on to fit the new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipelines.
    If you need to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
    Next, position the tap in the mounting opening in the bath/basin ensuring that the washing machines are in area in between the faucet and the sink. Protect the tap in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former kind should be linked to the faucet ends initially, tightening only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.

    Setting up the Tub


    Using both wooden boards under its feet, place the tub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
    The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the tub till the spirit level checks out degree.
    To set up faucets, fit the bottom of the furthest versatile tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
    Activate the water supply and check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the tub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
    Ultimately, deal with the bath paneling as described in the manufacturer's user's manual. Tiling and sealing around the bath tub must wait up until the tub has been utilized at least when as this will settle it into its final position.

    Preparing for the Setup


    Firstly, the supporting framework supplied with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to avoid stress on the bath tub.
    Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of all of the supplied washers.
    Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be suited its final setting.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall in between the bath as well as the tiling, leading to issues with dampness and possible leakages to the ceiling listed below.
    You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to allow for the activity experienced when the tub remains in use. The sealer can crack relatively early if you do not think about this motion prior to sealing.
    Conversely, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof adhesive as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    I came across that page on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing research the internet. Sharing is caring. You won't know, you could be helping someone out. We recognize the value of reading our article about Installing A Bathtub.




    Top Article


    Report this page